Media Mixage

Media Mixage Monday – Make a stamped metal bracelet for a friend! New Video

September 30, 2013 by admin

I’ve always had a fascination for words, even when I was a little girl. I loved to write and doodle.

It’s always interesting to me where I get my inspiration. I was reading through my facebook newsfeed and came across my cousin’s post about her little girl wanting to buy matching Mommy/Daughter jewelry. A light bulb went off and I thought “Wow! I could make that with my dies and Artisan X-plorer!” and so I did.

For me creating is very personal, it’s a bonding experience with friends and family and many times, handmade gifts are what they receive from me.

That’s why this type of jewelry really resonates with me. There are so many fun shapes in the Spellbinders® MediaMixáge™ line I know you’ll have fun making your own special, personalized jewelry too!

So in this video, I show you how to use metal alphabet stamps to create a metal stamped bracelet.

I would LOVE if you would let me know how you liked this project, so please leave comments below 🙂

And don’t forget to subscribe below so you don’t miss any of the projects 🙂

Click here to view the video on my youtube channel

More Jewelry Making videos – click here

How to make a Stamped Metal Wrap Bracelet

Designed by: Linda Peterson

MMM-001 Spellbinders® Artisan X-plorer™ machine

MD1-003 Spellbinders® Media Mixáge™ Rectangles One die template (used in project)

MM1-003 Spellbinders® Media Mixáge™ Copper sheet

MB6-006 Susan Lenart Kazmer for Spellbinders® Media Mixáge™ Turtles One brass blank

Miscellaneous beads and charms of choice

Alcohol based markers in colors of choice

Silk ribbon or cording of choice

Toggle or clasp

2 eyelets

Jump rings

Permanent marker

Crop-o-dile punch

Needle tool

Metal Alphabet Stamps

Ball peen hammer

Jewelry hammer with plastic end

Bench block

Nail file

Jewelry pliers

Optional dies suitable for this project:

MD1-001 Spellbinders® Media Mixáge™ Ovals One Die

MD1-012 Spellbinders® Media Mixáge™ Circles Three die

MD1-002 Spellbinders® Media Mixáge™ Squares One Die

Optional Brass Blanks suitable:

MB6-001 Susan Lenart Kazmer for™ Spellbinders® Media Mixáge™ Frames One

MB6-002 Susan Lenart Kazmer™ for Spellbinders® Media Mixáge™ Dresses One

MB6-009 Susan Lenart Kazmer™ for Spellbinders® Media Mixáge™ Hearts Three

Cut out a rectangle from the copper sheet using the #2 (with #1 being the smallest) Rectangles One die template using the Artisan X-plorer™ machine.

Lay die cut shape on to bench block. Hammer flat with the plastic end of the hammer and smooth edges with nail file.

Draw a line down the center vertically with a permanent marker. Draw a horizontal line for each line of the phrase you are going to spell out.

Position the alphabet stamp on copper die cut and tap firmly straight down with the hammer. Try not to tap too many times as this can distort your letter. Repeat until word or phrase is spelled out.

Color over letters with permanent marker and let dry.

Sand the top of the copper with nail file, leaving only the black in the lettering.

Punch hole where desired with Crop-o-Dile and insert eyelet from the front.

Flip over to back side and tap around the edges of the eyelet with ball peen hammer. This will cause the sides to “mushroom” out so that the eyelet is securely in place.

Measure length of silk ribbon/cord. It should be long enough to wrap around wrist three to four times. Thread silk ribbon/cord through eyelet hole on front and up through the back on the opposite side. Attach toggles/clasp with jump rings.

Embellishment

Gently hammer a texture into the small turtle using the ball peen side of the hammer.

Color with desired markers. As markers touch each color they will blend and mottle. Allow to dry.

Punch a small hole with needle tool where you would like your dangles to hang from. Attach to bracelet with jump rings along with miscellaneous beads and charms.

Don’t miss out! Subscribe to my free project tutorials, videos and tips to help you in your creative home and business life! Enter your email address:

Delivered by FeedBurner

Mixed Media May – Get ready for fall and make these adorable paper pumpkins

September 23, 2013 by admin

Hello Everyone! Happy FALL! Finally – cooler crisp temperatures are here!

My most FAVORITE time of the year – mostly because of pumpkin pie! I always get inspired this time of year because I love the cool crisp air how mother nature paints the landscape with gorgeous rich colors. It’s not uncommon for me to dress up our dinner table with whimsical napkins and décor. These little pumpkin place card holders are easy and quick to make with just a few supplies. You’re guests will not only love them, but will love to take them home as a little momento of the evening.

So today I’m showing you how to make adorable paper pumpkins from paper. These are great place card holders but would be even cuter made from smaller circles and used as cupcake toppers!! ADORABLE!

Hint: These are make great party favors and also little photo holders. Don’t you just love projects that are easy AND versatile?

Love this project? Pin it! and share it!

Can’t see the video? Click here

Project Dimensions: Varies

Spellbinders Supplies:

MMM-001 Spellbinders® Artisan X-plorer™ machine

MD1-012 Spellbinders® Media Mixáge™ Circles Three die

MD1-010 Spellbinders® Media Mixáge™ Hearts Two Die Template (optional)

MD2-004 Spellbinders® Media Mixáge™ Flowers One die template

MB3-001 Spellbinders® Media Mixáge™ Circle Hatpin – Bronze

S5-120 Spellbinders® Fall Foliage die templates

Raffia

2 to 3 small buttons

3 – 4 x 4” squares of burlap (optional)

Dictionary paper or newspaper

Ink pad in a pumpkin orange color

Tacky Glue

22 gauge steel annealed wire (available at hardware stores)

Needle nose pliers

Round nose pliers

Wire cutters

Scissors

Cosmetic sponge

As a variation of shape use these same instructions but substitute the #3 Flowers One die template.

Stack and fold for sheets of dictionary paper in half to create 8 layers.

Cut approximately 20+ circles from the dictionary paper using the #3 (with #1 being the smallest) Circles three die template. (hint: the more you cut the fuller your pumpkin)

Apply orange ink with cosmetic sponge to both sides of circles

Cut approximately 1/8” off of the bottom of all circles to create a flat base

Fold circles in half

Stack all the folded circles and match edges.

Apply glue to the folded edges and press firmly for a minute or so with your fingers.

Release and the shapes will fluff and turn into a pumpkin.

Working off the spool create a loop with a long wire extention. Bend the wire around the loop a couple of times and curl the remaining wire.

Snip off spool leaving approximately 3 inches of a tail. Apply glue to tail and place in center of pumpkin for stem.

Create a coil with round nose pliers and leave a 3” extension. Glue into the center of pumpkin.

Optional: cut three leaves of burlap using the Fall Foliage Red Maple leaf die.

Glue burlap leaves to bottom of pumpkin

Embellishments:

Cut a flower from the #2 flowers one die and ink

Pull the wire from the hatpin.

Glue flower to back of hat pin and glue buttons to front center.

Create a small bow with raffia

Glue to front of the pumpkin to embellish.

Don’t miss out! Subscribe to my free project tutorials, videos and tips to help you in your creative home and business life! Enter your email address:

Delivered by FeedBurner

Mixed Media Monday – How to turn shrink plastic into fabulous looking rustic metal earrings – Spellbinders Media Mixage

September 16, 2013 by admin

I’m drawn to pieces that tell a story. I believe that’s why I like all things vintage and if they could – these pieces would tell us an incredible story.

When I look at these earrings, I remember my first trip to Paris with my friend and editor Marie. We had just finished photography for my book Metalwork Jewelry. She couldn’t believe that I would just pick things up wherever I found them, even if they were on the side of the road, and use them in my artwork. Well, after a week in the studio with me, she changed her mind. While in Paris and just in front of the Eiffel Tower, I looked over to find her kneeling down, digging in the dirt with her keys to retrieve and old bottle cap.

I recently ran across an inspiration board on Pinterest that was all about rusty metal and turquoise patina. I loved the colors together and the way that the patina seemed to dance on the metal.

I thought these colors were just gorgeous for fall and since I love all things old and worn, I decided to have a play and Explore Beyond at creating my own rustic metal shapes. I love that I have a sense of control, yet at the same time, each piece was unique in its own way.

I hope this tutorial really inspires you to explore unconventional ways to use conventional materials. There’s so many ways to incorporate this into your mixed media artwork and jewelry. Have fun!

Faux Rusty Metal from Shrink Plastic

Project Dimensions: Varies

Spellbinders Supplies:

MMM-001 Spellbinders® Artisan X-plorer™ machine

MD1-001 Spellbinders® Media Mixáge™ Ovals One Die

MD1-012 Spellbinders® Media Mixáge™ Circles Three die

MT1-005 Spellbinders® Media Mixáge™ Grate Works Three texture plate

Shrink plastic – Graphix, Inc Inkjet Printable Shrink Film

Dark brown acrylic paint

Gilders Paste® Patina

Heat tool

Tweezers

Heat resistant work surface (such as a fire brick or metal tray)

Jump rings

Earring wires

Cosmetic sponge

Drill with a 3/32” drill bit or size of choice

Block of scrap wood

Optional supplies: charms, feathers, vintage finds, additional colors of acrylic paint such as copper, bronze, gold, 1/8” circle hand punch

Note: I drill my holes with a drill because I can place the holes exactly where I need them. Sometimes the holes shrink too small when I punch them before heating.

Cut your shapes from shrink plastic using the Circles Three and Ovals One die templates of choice. Don’t throw away your negative space as this can be used for the focal base for a pendant if desired. (note you may punch holes into your shapes at this stage with a 1/8” hand punch)

Place your plastic shapes onto a heat resistant surface. Apply heat. As the shapes melt, they will curl up and then flatten back out again. Use long tweezers to protect your fingers from getting burned.

While the plastic shapes are still hot, stamp them with the texture plate with firm pressure.

Paint with acrylic paints and allow to dry.

Apply Gilders Paste with your finger or a cosmetic sponge as desired.

Place shapes onto a block of scrap wood and drill holes

Arrange shapes and attach as desired with jump rings. Add embellishments and earring wires.

Don’t miss out! Subscribe to my free project tutorials, videos and tips to help you in your creative home and business life! Enter your email address:

Delivered by FeedBurner

Handbag, Shoes and bling perfect for the red carpet – EMMYS inspired!

September 10, 2013 by admin

A couple of Monday’s ago, Spellbinders and I kicked off a month long event celebrating their walking the red carpet at the Emmy awards with a video tutorial featuring my “Evening at the Emmys” glam earrings (to view the post and video click here) It’s a special honor for Spellbinders and really for crafting in general as the stars will get a glimpse into our work of creativity!

My friend Beck Beattie, from Australia, took inspiration from the video and created the perfect compliment to my earrings! I just love what she did! And she did a great tutorial – so check her out on her blog for the how to and get your glam on! – CLICK HERE

Don’t miss out! Subscribe to my free project tutorials, videos and tips to help you in your creative home and business life! Enter your email address:

Delivered by FeedBurner